Skip to content
Austin Air Conditioning Solutions (469) 771-1630
An air conditioning technician crouching beside an outdoor condenser unit at the side of a house, reading a digital gauge wired into the unit

Refrigerant Leak Repair in Austin, TX

We locate and repair AC refrigerant leaks in Austin and nearby communities.

Call (469) 771-1630 Ask a question

Turning the thermostat down, changing a dirty filter, or rinsing leaves from the outdoor condenser are sensible first steps when an AC system starts blowing warmer air. Those checks can improve airflow and reduce strain on the equipment, but they cannot replace refrigerant that has escaped through a coil, copper line, valve core, or fitting.

A refrigerant leak can be small enough that the system still cools for part of the day, especially when the thermostat is set lower than usual. Adding refrigerant without finding the leak may bring the temperature down temporarily, but the charge will continue to fall and the compressor may run longer than it should.

This is work that should not be left to wait once the cooling output has changed or ice appears on the refrigerant line. Low refrigerant can drive coil temperatures below freezing, build ice on the evaporator coil, and leave the compressor working with conditions it was not designed to handle.

Warm air and hissing

Customers often call us because the vents are blowing warm air while the outdoor unit is still running, or because one room never reaches the temperature shown on the thermostat. A weak stream of cool air is different from no airflow at all: the blower may be moving air normally, but the evaporator coil may not have enough refrigerant to remove heat from that air.

A hiss near the indoor air handler, outdoor condenser, or copper line set can point to refrigerant escaping under pressure. Other signs include ice on the larger insulated copper line, frost on the evaporator coil, oily residue around a service valve, or water around the indoor cabinet after ice melts. Some systems also cycle off on a pressure safety switch before the house has cooled.

These symptoms can overlap with an airflow restriction, a failing blower component, a dirty coil, or a control issue, so the sound or ice alone does not identify the failed part. A leaking Schrader valve, a rubbed-through line, and a corroded evaporator coil are separate repairs with different materials, access work, and charges to restore the system.

Leak test callout

On a leak test callout, we start with the thermostat setting, indoor temperature, supply-air temperature, filter condition, coil condition, and visible copper lines. We inspect service ports, flare connections, braze joints, the condenser coil, and the evaporator coil cabinet for oil staining, corrosion, rubbed insulation, or damaged tubing. We also read the system’s operating pressures and compare them with the equipment type, outdoor temperature, and manufacturer charging method.

Electronic leak detection, soap solution at accessible joints, and pressure testing can help narrow down a leak that is not visible. An initial inspection commonly takes about 30 to 60 minutes when the service valves, line set, and outdoor unit are accessible; a concealed evaporator coil or a line set inside a wall can take longer to isolate. A valve core, cap, exposed fitting, or accessible section of copper tubing can often be addressed during the same visit after the leak is confirmed.

When a coil needs to be removed, a line set runs through a finished wall, or a manufacturer-specific coil has to be ordered, we explain the repair path and arrange the return work. After a repair, we evacuate the sealed circuit, verify that it holds vacuum, and recharge the system using the method specified for that equipment rather than treating the pressure reading alone as the final check.

Evaporator coil and line access

The leak location changes the scope of the repair more than the symptom does. A service-port valve or accessible outdoor fitting is reached at the condenser cabinet, while an evaporator coil may sit behind panels in an attic air handler, a closet furnace cabinet, or a tight indoor plenum. Copper tubing that disappears into a wall, ceiling, or slab can require more investigation than a line set mounted along an exterior wall.

Equipment age and refrigerant type also matter. Older coils can show widespread corrosion rather than one repairable pinhole, and a replacement coil may need to be ordered by the model and serial number on the data plate. The final scope can also change if insulation must be replaced, a damaged line needs a new section, or access panels have to be removed and reinstalled to reach the leaking connection.

Model plate and unit location

Before calling, check the model number on the metal data plate of the outdoor condenser or indoor air handler. The plate is commonly behind a removable service panel or on the exterior cabinet, and a clear photo helps us identify the refrigerant type and possible coil match.

Let us know which room has the indoor unit or where the air handler is installed, such as an attic, garage closet, hallway closet, or crawlspace. Mention whether the AC is running now, whether there is ice on the copper line, and whether water is dripping from the indoor cabinet.

If the outdoor condenser is behind a gate, beside a fence, or under dense shrubs, tell us about that access as well. We cover Austin, Rollingwood, West Lake Hills, and Lost Creek from 5555 N Lamar Blvd.

Call Austin Air Conditioning Solutions at (469) 771-1630 with the model plate photo and unit location. Waiting on a refrigerant leak can allow ice to spread across the evaporator coil and put added strain on the compressor.

Hours of operation

MondayOpen 24 hours
TuesdayOpen 24 hours
WednesdayOpen 24 hours
ThursdayOpen 24 hours
FridayOpen 24 hours
SaturdayOpen 24 hours
SundayOpen 24 hours

Not what you were after? Go back to the home page or ac drain line cleaning.